10 Band I2C Graphic Equalizer Circuit - 16F628 TEA6360

Updated:

• 2016-08-17 - Added small application for calculate frequencies and parts.

10 Band Equalizer

A graphic equalizer is a high-fidelity audio control that allows the user to see graphically and control individually a number of different frequency bands in a stereophonic system. A typical graphic equalizer consists of several audio filter/amplifiers, each centered at a specific frequency in the audio range. Most graphic equalizers have two identical sets of filter/amplifiers, one for each channel in a stereophonic system.

The gain controls in most graphic equalizers are slide potentiometers that are adjusted by moving a controller up or down. Gain is increased by sliding the upwards. The slide potentiometers for each channel are placed side-by-side, with the lowest-frequency unit at the left and the highest-frequency unit at the right. In this way, the positions of the buttons appear to follow a graphical curve that represents the gain as a function of frequency for each channel.

By using following circuit you can build a 10 band stereo graphic equalizer that can be controlled via I2C system. For this circuit I used two of TEA6360 ICs. Each IC contains two serial five bands equalizer blocks. Therefore, we need two ICs for 10 bands. We can reduce the size of circuit because all the function can be drive via i2C. So that, we do not need connect potentiometers to control the gain of frequency bands like an ordinary equalizer. In addition, we can reduce cost and complexity of circuit using this IC.

Schematic

Circuit on PCB

In my demo code, I used 16F628A micro-controller and single button to set equalizer modes. The modes are ‘Flat’, ’Rock‘, ’Pop‘, ’Jazz‘ and ’Party’. The status will indicate by five LEDs those connected to PORTA. In addition, selected mode saved to device Eeprom and load to ICs when start up. However, according to your choice you can able to change the code.

For example if you need to set gain for each frequency manually, then you can add 1 button to each channel and total 10 buttons. For another example, you can add 3 buttons. One button to raise the gain and other to lower and 3rd one for select desired frequency.

The center frequency of each bands are 31Hz, 62Hz, 125Hz, 250Hz, 500Hz, 1KHz, 2KHz, 4KHz, 8KHz and 16KHz. the Q (quality) factor is 1 to 1.2 and PCB, full schematic and sample code can be downloading in below.

Part List

• C04, 07, 08, 09 = 0.37uF
• C10, 11, 12, 13 = 0.18uF
• C14, 15, 16, 17 = 0.01uF
• C18, 19, 20, 21 = 0.047uF
• C22, 23, 24, 25 = 0.022uF
• C27, 28, 30, 31 = 0.01uF
• C32, 33, 34, 35 = 0.0052uF
• C36, 37, 38, 39 = 0.0027uF
• C40, 41, 42, 43 = 0.0015uF
• C44, 45, 46, 47 = 720pF

TEA6360

The 5-band stereo equalizer is a 12C-bus controlled tone processor for application in car radio sets, TV sets and music centers. It offers the possibility of sound control as well as equalization of sound pressure behavior of different rooms or loudspeakers, especially in cars.

FEATURES

• Monolithic integrated 5-band stereo equalizer circuit
• Five filters for each channel
• Center frequency, bandwidth and maximum boost/cut defined by external components
• Choice for variable or constant Q-factor via I2C software
• Defeat mode
• All stages are DC-coupled
• I2C-bus control for all functions
• Two different module addresses programmable.

10 Band Equalizer
Calculator App