Thursday, November 26, 2015

Simple and Accurate LC Meter Circuit - 16F690

Simple and Accurate LC Meter - 16F690
Digital LC Meter

A LCR meter [Inductance (L), Capacitance (C), and Resistance (R)] is a piece of electronic test equipment used to measure the inductance, capacitance and, resistance of a component. Inductance is the property of an electrical circuit causing voltage to be generated proportional to the rate of change in current in a circuit. In Electronics, capacitance is the ability of a body to hold an electrical charge. Capacitance is also a measure of the amount of electrical energy stored (or separated) for a given electric potential. The electrical resistance of an electrical element measures its opposition to the passage of an electric current. The meter reads L, C and R directly with no human calculation required.

Recently I found this LC meter project on internet and I was looking for that kind of project. Therefore, I build. Amazing it is work! Also the accuracy of this LC meter is great and it is very easy to build. So that, I post it here, because I think it is useful to you. You can visit original post from using this link: LMC3

The data below were determined based on theoretical calculations, the scale and the display automatically change.

Min Max Resolution Accuracy
Non Polar Condenser 1pF 1nF 0.1pF 1%

1nF 100nF 1pF  1%

100nF 1uF  1nF 2.5%
Electrolytic Capacitor 100nF 100,000uF 1nF 5%
Inductor 10nH 20H 10nH 5%
Resistance 1mΩ 0.5Ω 1mΩ 5% 
Inductance 0.5Ω 30Ω 10mΩ 10%
Specifications of the LC Meter


Simple and Accurate LC Meter Circuit
LC Meter Diagram


LC Switch:
The purpose of this is, switch between inductance and capacitance mode. When you turn on the LC meter, you should set it to C mode.

Calibration Switch:
You can calibrate LC meter by pressing this. See Calibration for more details.

LC Meter Calibration

You have 3 modes to calibrate. When the process is completed, calibrated values are saving to the microcontroller’s internal EEPROM, so of course they are available after the re-start.

C Calibration
  1. Switch on
  2. Switch L/C switch to C position
  3. Leave the test probes freely. Do not even touch it
  4. Press and hold the CALIB button until the message Switch to meas. Then release the button
  5. Wait for the appearance of 0.00 pF
L Calibration
  1. Switch on
  2. Switch to the L position
  3. Connect L/C probe and GND probe together
  4. Press and hold the CALIB button until the message Switch to meas. Then release the button
  5. Wait for the appearance of 0.00 uH
ESR Calibration
  1. Switch on
  2. Switch to the C position
  3. Connect LE probe and GND probe together
  4. Press and hold the CALIB button until the message Switch to meas. Then release the button
  5. Note the value shown on the screen
Calibration Values
  • F0 = 499.9k
  • Fcal = 355.9k
  • Re = 180Ω
  • Uesr0 = 58.3mV
  • Fesr = 83.6k
  • Rx = 0mΩ [-5mΩ to 5mΩ]

Critical Components

All the below resistors are 1%.
(In my circuit, I used normal resistors and those are measured using digital multimeter)

  • 47Ω - R11
  • 47kΩ - R8
  • 100kΩ - R3-R5
  • 1nF - C8, C11 (Polypropylene or Polyester)
  • 33nF - C10 (Polypropylene 275V AC)
  • 10uF - C7, C9 (Tantalum)
  • 100uH - L1 (Low-loss DC resistance of 0.3-0.4Ω)

Testing


Simple and Accurate LC Meter Circuit - 16F690 test c
check 22pF ceramic capacitor

Simple and Accurate LC Meter Circuit - 16F690 test e
check 100uF electrolytic capacitor

Simple and Accurate LC Meter Circuit - 16F690 test l
check 100uH inductor

I was unable to find a reed relay, so I put 5v ordinary relay temporarily. In addition, my PCB designed for the TL2285 switches. But, I bought TL2230 by mistake :)

If the back-light brightness is low, you can increase back-light brightness by decreasing the value of the resistor R2 to 470Ω - 1k. You can change display contrast by adjusting 10k preset.
For PCB, Schematic and hex file, click download button.

You need to discharge capacitors properly before measuring.

Posted By :

Please Note: All contents provided on this blog are for non-commercial purposes only.
Any question..? Feel Free to Ask!

Drop your Comments below. Please report broken links to here
  1. how many capacitor value mesuring this project..

    ReplyDelete
  2. other ic use this circuit?what is the same ic this project?

    ReplyDelete
    Replies
    1. Only single Ic is use for this circuit and its very cheap. its cost about LKR 200.00

      Delete
  3. why this circuit using relay....
    my circuit not mesuring non polar capacior...

    ReplyDelete
    Replies
    1. This is not my project. Please find the original post from here. http://www.hobbielektronika.hu/cikkek/lcm3_alkatresz_mero_muszer_-_kit_lehetoseg.html

      Delete
  4. assemble the entire project but when I light it up does not show anything the display

    ReplyDelete
    Replies
    1. Check whether relay work or not when connected to the power. if you hear sound from relay then check display connection. Also check MCLR pin

      Delete
  5. Thank you for the answer, I hear that the relay is triggered when I connect the energy use this model N4078-05-50 5V - 50W - 50Ohm. Can i remove the relay to test if truly i turn on doing a jumper?

    ReplyDelete
    Replies
    1. If the relay triggered when power applied to the circuit, then check your LCD. and also make sure the chip was correctly programmed.

      Delete
  6. Hello scorpionz I cannot make a pledge the LC, you said that verify the MCLR but not as doing so, apology for my stupid questions but I started at the Electronica makes my little time and there are still things that are not. The pin positive relay i always have 0v

    ReplyDelete
  7. I am having issues trying to load the hex file using my pikit2

    ReplyDelete
  8. Dear sir,
    Please can you send me the project file. Thanks. okeykamalu@gmail.com

    ReplyDelete
    Replies
    1. http://www.hobbielektronika.hu/cikkek/lcm3_alkatresz_mero_muszer_-_kit_lehetoseg.html

      Delete
    2. Please Scorpionz, can you send me the hex file. The website is not written in English. Thanks.

      Delete
    3. Click download button and get the link

      Delete
  9. Is there any involvement of PCB Design Services ? Very neat explanations. Thanks for giving the exact values of inductance,resistance and capacitance to be used for the electronic circuits.It is noted that the circuit board should be designed in a way that connects all the pathways to perform the function.

    ReplyDelete

 

on line

Labels

Recent comment

Visitors

Free counters!
Copyright © 2012 - Scorpionz™.,All rights reserved | Powered by Blogger